MYPIN TA4 PID Controller, The MYPIN TA4 PID is one of the better controllers from China. Here is a copy of the actual instructions that ship with the controller . JConn Inv. PID Controller Instruction Manual This information is specific to the Mypin TA4 based controller sold by JConn Inv. but it should work for most TA4. Anyway, the manual did not come with the MYPIN PID. Does anyone have a link to the MYPIN PID manual? Manual for Mypin TA4.

Author: Samuzil Medal
Country: Austria
Language: English (Spanish)
Genre: Sex
Published (Last): 28 August 2007
Pages: 410
PDF File Size: 16.93 Mb
ePub File Size: 10.46 Mb
ISBN: 222-6-79690-383-6
Downloads: 98321
Price: Free* [*Free Regsitration Required]
Uploader: Shaktishakar

Apr 10, 9. Now with us turning the parameter to off the hysteresis or whatever is not valid and won’t operate correct? There’s also a video tutorial on the manual Mypin ta4 manual found too. Saw the part about setting maanual to Like TardisSmoker said, with the P value set to off, it’s basically a dumb thermostat. Press mypin ta4 manual green UP button and the display will change to flashing F 6.

Pid build, issues is it the pid or the wiring ???

Apr 9, 1. I think you are manuall the point of completing the smoker and seeing how the unit runs as a whole. When you release the probe, it slowly radiates the heat it absorbed from your hand mypin ta4 manual, and cools lower than it heated. Apr 9, 2.

Ta4 Wiring Diagram – Wiring Diagram •

Do you already have an account? Apparently it is in the lessons learned, and much simpler. In my ice water after manaul ice sit in there three minutes and 1 stir.

Press and hold “set” button for 3 seconds. mypin ta4 manual

How do I change the temperature I’d mypin ta4 manual to extrude? This means that it is autotuning and you should now leave it alone until it stops blinking. It’s in the manual I referenced above. To run an auto tune cycle, it’s pretty simple.

Not that I am aware of. Close enough for cooking. Apr 10, Search Media New Media. Is there something else I should check or is this normal in pid adjustments. Next issue mypin ta4 manual sure if it is a issue but I did he ice water trick for probe caliberation.

Press the SET button when you are done. You can put a few bricks on the rack of the smoker to mypin ta4 manual the meat as the bricks will soak up some of the heat similar to the way meat will. Press “set” until “HYS” 6. Hold down the SET button until the top display displays the temperature.

I grabbed the tip of the probe for a quick second mypin ta4 manual it climbs fast but over shoots the temp by quite a bit. This puts mnual in Menu mode. That was the mypin with the ssr model?? I will start the wiring soon and hopefully be ready to test. Dward mentioned an auto tune mode which not sure mypin ta4 manual that one how to do it?? Brandon, I just received your PM and sent you a reply. Tw4 luck with you smoking. If you were to stick it into a glass of room temp water, it would drop fairly mypin ta4 manual.

I’m a chatter box today lol just trying to get it dialed in. Active topics Unanswered topics. Thanks, but I was hoping for an operations manual. I set that parameter p in the pid programming from I think I had 8.

I will try changing that and see what happens Here is a copy of the actual instructions that ship with the controller: Setting your controller temperature. Again thanks guys for all the help this forum is a true mentor in general and all of you advocates that swing the knowledge are awesome!!

I think it is in the PID setup. Tardis have mypin ta4 manual done this with your mypin also looking for a way to verify he probe is caliberated and reading properly. Homebrew kegging and draft beer tapping equipment including aluminum CO2 tanks, CO2 regulators, quick disconnects, Cornelius kegs, beer taps, pony taps, beer hardware, hoses and fittings.

How precise do you need to control the temp. Set the PID temperature to your normal mash temperature 5. Mypin ta4 manual there is a way to get it to control finer, I don’t know how. I don’t mypin ta4 manual about the other kind. Yes, my password is: It can then anticipate with fairly high precision when heat mypin ta4 manual be needed. I set it up originally like I stated, but then tried the “Learn” mode and got the rapid cycling.

Are you using a Filastruder or a flamethrower?