HEF Datasheet, HEF PDF, HEF Data sheet, HEF manual, HEF pdf, HEF, datenblatt, Electronics HEF, alldatasheet, free. 15 Apr Data sheet acquired from Harris Semiconductor. SCHSC − Revised October HCDB consists of an oscillator section and CMOS Stage Ripple-Carry Binary Counter/Divider and Oscillator. CMOS Stage Ripple-Carry Binary Counter/Divider and Oscillator – CDB. Datasheet.
|Published (Last):||3 May 2005|
|PDF File Size:||18.54 Mb|
|ePub File Size:||11.62 Mb|
|Price:||Free* [*Free Regsitration Required]|
We haven’t talked about the carry from the seconds counter to the minutes counter yet.
IC2 also contains a 14 bit divider hef4060 datasheet. Yef4060 IC9D will inverse the pulses coming from the push button. Next stop, the minutes counter.
Hef4060 datasheet other sheet covers the display circuit and the power supply. The carry from the seconds counter is constantly high, with only a short carry pulse every 60 seconds. C5 is used to set the correct frequency.
CDB CMOS Stage Ripple-Carry Binary Counter/Divider and Oscillator |
Otherwise the roll over of the hef4060 datasheet counter hef4060 datasheet advance the hef4060 datasheet counter too. But this time the maximum count value is limited to As hef406, with such a one of project, I didn’t bother to create a PCB for the project. What is IC3B doing there? IC4A divides the 1Hz pulse by The Buttons Let’s start simple, the buttons, which are used to set the time.
Please consider clicking on the Support Me button to show your appreciation. Everything is built on pad board using Road Runner wiring to connect all the components together. These kind of capacitors usually have a hef4060 datasheet line on top of their body. It’s a bed side table clock, I don’t need it to light up the entire room at night, you know.
This reset hev4060 is also used as carry to the hours counter. datasgeet
CMOS 14-Stage Ripple-Carry Binary Counter/Divider and Oscillator
OK, that’s enough for this one page. This pulse is very short because its cause is removed by the reset almost instantly. Once the counters reach that state hef4060 datasheet are reset back to 0 hef4060 datasheet. You can download the circuit diagram here.
I don’t need the hef460 of datasheeh seconds counter itself, because I do not have a seconds display. This pulse hef4060 datasheet used to flash the colon between the hour digits and the minute digits on the display.
The Time Base IC2 forms the time base oscillator and first pre-scaler stage. IC2 forms uef4060 time base oscillator and first pre-scaler stage. This signal is fed to the seconds counter, satasheet described below.
This helps hef4060 datasheet tune the frequency of the time base to the correct value. While the clock is in run mode SET is high, opening the gate for the carry pulse.
We’ll have to tell the clock what time it is when hef4060 datasheet has lost all hef4060 datasheet power anyway.
Eventually the output of IC10C goes high when a button is pressed. Hef4060 datasheet the carry pulse goes high too, the output of IC9B goes low briefly. From then on the flip-flop remains in that state, until the hours counter is reset to 0 again.
Hef4060 datasheet the end it will produce an accurate frequency of 2Hz on output pin 3. This allows you to accurately datashest the clock with a known good time source.
dahasheet On the next page I’ll explain the display circuit and power supply of the clock. However hef4060 datasheet would require one extra chip for just one gate, whereas I had a spare flip-flop available which could hwf4060 ab used for the same job. This is a nice 0.
Therefore IC9C will inversely follow the low going carry signal hef4060 datasheet the minutes counter. We are only interested in two others, the Hz and the 64Hz outputs, which are used in the display section of the clock. The Minutes Counter Next stop, the minutes counter. The CLK input to the flip-flop is low, because the hours counter has just been reset hef4060 datasheet 0.
While the clock is in SET mode there won’t come any carry pulses from the minutes counter and that signal is constantly datsheet. Let’s start simple, the buttons, which are used to set the time. Together with this knowledge you should hef4060 datasheet able to build hef4060 datasheet clock yourself too. It also produces several other division ratios. It’s output Q0 of the first decade counter IC4A.
It is hef4060 datasheet over two hef4060 datasheet, one sheet covers the time base and the seconds, minutes and hours counters. When the clock is switched to SET mode though, the SET line goes low, which keeps the reset line to the seconds counter constantly high, preventing the seconds counter to count.
And now the hours counter. This page will describe sheet one in detail, while the next page will describe sheet number two. In SET hef4060 datasheet the SET signal is high, and the seconds to minutes carry can never occur because the seconds counter is held in reset. The datashee of the resistor value has no effect on the precision of the time base B.